This instruction manual describes preventive maintenance and quick FANUC SYSTEM 3T-MODEL C is designated to be assembled inside an NC machine. Fanuc System 3T-Model D Operator’s Manual(BE 02) – Free download as PDF File .pdf) or read online for free. I am looking for an operators manual for a Fanuc 3 T controller used on a small Wasino gang lathe. Any help would be appreciated. Going to.
Let me know if I can help with what documation I have. A PM conversation with memoryman is giving me hope.
Thanks fordav11, that worked! I would like to find a manual that goes into the disambly of the head manua and slides.
Fanuc 3t Manuals
I’m using basic G-code group A and the very basic M codes to try to program this thing. The ballscrews were actually fresh and the table had no appreciable backlash less than a tenth of a thou.
I’m wishing Fanuc had more info on these older units.
Program input is not started with the data input external start signal MINP. So my question probably should be. Need help understanding “zero” on a Fanuc 3T.
Majual from what can see, Tsugami may not have made the actual spindle. If you don’t have the manual and can’t get your machine working with those other parameters let me know and I’ll scan the parameter descriptions and settings pages from my manual 15 pages.
I have work offsets which I can set with G10, G54, etc.
I’m not an expert fanud reading these things, but it looks like this machine has 8K of memory? The first thing I did when I got it home was power it on to see if the parameters were still intact. Fanuc paramater’s yaddatrance I should be able to help with paramater list I will dig up my book’s and look. Me Where exatly are you I’m in the midwest U.
I know I had to tweak a bunch of parameters fanyc mine because even though the original company bought a lot of options, it’s obvious they never used a lot of them since the related parameters either had default values or nothing. Al to the rescue again: You must set the tools using G50’s. I’ve cut a couple things on it since the G50 discovery, the first cut was this buffer. I have 6T and 0T maintenance manuals but I dont suppose the parameter list from these will work or can some be used just to check if the Hydraulics come on etc.
Fanuc 3t Manuals User Guides – CNC Manual
Is that even possible on a 3T control? Let me know if there’s anything I can do to help you with your unit! I was figuring that you do the same thing on a lathe.
I have tool offsets which are settable from the MDI. Imagination will take you everywhere. The time now is Another thing that originally manuwl me for a loop was that the X axis was specified in diameter.
Anybody has any idea what that means? Last edited by Kevin Taylor; at Similar Threads fanuc 11m parameters By sootblower in forum Fanuc.
First If you can post more pic’s, How Deep did you go into the mechinacal of the Lathe Bearing’s and such I have machine of the same model I have maintnace manual’s and programing with paramiter list’s If I can Help at pressent mine is down with a spindel drive issue I have Igbat’s to replace and have so far replaced one the local frelance Fanuc tec told me that the top one was the most likley to be the one dead but no change in symptom’s after changing it will move on and test as I change to hopefuly find the proublem.
Maybe you can tell me, a mystery item to me on the spindle is what looks like an air driven indexer. MINP isn’t defined anywhere in the maintennace manual or the electrical manual. Results 1 to 10 of Now I just need to figure out if there’s any way to set DNC on this machine So if the table moves 1″, the readout said 2″. I have a “random” zero which is wherever the table was on power-up.
Program input is started with the data input external start signal MINP. Fanuc paramater’s Yaddatrance are you in the US Location? You will need it several times. There are some advanced tricks to avoid re-setting G50’s for each job but 3y with this simple method first. Cold and snow now so inside work will maybe get cought up Good luck Kevin. By roymanvega in forum Fanuc.
Fanuc 3T Parameters Manual
By the way good work on the retrofit. I worked a 3T many fwnuc ago. Posted via Mobile Device. In my 21 those parameters start at There are integers, not bits, so they are easy to identify. While you do not have a parameter manual you can see if you have those parameters.